Product Description- Masters OGS-3 Synthetic Gun Oil has been specially formulated using a proprietary basestock which adds polarity to attach to metal and repel charged dust particles. It is extremely thermally stable with a very low volatility for long lasting lubrication. Selected additives have been included to provide advanced corrosion protection, improved lubricity and anti-wear protection. Masters products contain no Chlorine, Teflon (Reg. Trademark of Dupont), Moly or graphite. This product will not become gummy or sticky with age, even under the most extreme conditions. OGS-3 will perform well from sub zero conditions to extreme desert heat. Whether you are a Military, Tactical Law Enforcement, Competitive Shooter, Hunter, Gunsmith or for Personal Defense, Masters OGS-3 Gun Oil will keep your firearm lubricated for extended periods under the most demanding conditions. Use of this product will help prevent hard carbon buildup, which occurs in some firearms due to design and demanding use. Cleaning will be much easier with the use of this product. When reliability is a must, this product should be your first choice. Packaged in a small convenient squeeze bottle with a flip top applicator, this product can easily be taken to the field, used on the bench or carried in the range box.
Directions for Use - OGS-3 may be applied various ways from quick field lubrication to a full breakdown for thorough cleaning and/or maintenance. Always use OGS-3 on all moving parts.
For field lubrication without thorough cleaning.
1. Make sure the firearm is unloaded.
2. Quick clean firearm with Masters Action and Gun Cleaners aggressive spray to wash away excessive dirt and grime.
3. Wipe dry with soft clean cloth.
4. Apply a liberal amount of Master OGS-3 to all moving surfaces of all moving parts.
For complete and thorough cleaning.
1. Allways make sure firearm is unloaded.
2. Disassemble firearm and clean each part with Masters Action & Gun Cleaner, using Masters Bore Cleaner for the bore.
3. Wipe dry with soft clean cloth.
4. Apply a liberal amount of Master OGS-3 to all surfaces of moving parts during reassembly.
5. Finish with a fine mist of Masters Gun Lubricant/Protectant followed by a soft clean cloth.
Go back to top
Masters Synthetic Grease
Go back to top - Print this Description
Product Description- Masters Synthetic Grease is a proven formulation providing superior performance against wear, friction and rust. Excellent stability between -40²F and 400²F, Masters Synthetic Grease also offers additional protection against rust and corrosion even in very wet conditions and is compatible with most plastics. Masters Synthetic Grease provides all around anti-wear, anti-fatigue and anti-rust protection. It also repels dust and dirt so it is ideal for all slides, springs, bolts, hinges and mechanisms that require lubrication.
Directions for Use
1. Make sure the firearm is unloaded.
2. Clean firearm thoroughly. Master Action & Gun Cleaner or Masters Bore Cleaner is recommended.
3. Using the fine tipped, re-sealable, pin-point syringe applicator, apply the proper amount of grease to all mechanisms needing protection. Note: For areas that Masters GS-2 Synthetic Grease can not penetrate, try Masters OGS-3 Synthetic Gun Oil.
4. Wipe off excess with finger or soft cloth.
5. Be sure syringe tip is rotated to the closed position prior to storage
Note: Use caution when using grease over walking surfaces. Small amounts of grease quickly spread on smooth walking surfaces rendering them very slippery. Masters yellow tinted formula may help in placement of applications. Be sure to clean floor thoroughly if grease is present on walking surfaces.
Go back to top
Masters Synthetic Spray Lubricant / Protectant
Go back to top - Print this Description
NOW AVAILABLE
Product Description- An advanced synthetic formula intended to provide lubrication and corrosion protection to firearms. This formula will provide wear and corrosion protection without excessive attraction of dust particles. Masters Synthetic Spray Lubricant / Protectant will not become gummy, tacky or sticky. The naturally polar nature of this product aids in its attraction to metal surfaces and repelling of dust particles. This product also aids in preventing formation of hard carbon residue in firearm actions.
Directions for Use
1. Make sure the firearm is unloaded.
2. Apply spray stream of the product to firearm surfaces.
3. Use spray extension tube to direct spray lubricant into inner areas of the firearm action.
4. Use cleaning patches or clean cloth to further distribute lubricant and remove excess.
Note: Use caution when spraying lubricant over walking surfaces. Over spray can cause a slip hazard and should be cleaned thoroughly if present on floors.
Go back to top
Masters Action & Gun Cleaner
Go back to top - Print this Description
NOW AVAILABLE
Product Description- An advanced formula for removing built up carbon powder residues, grease and lubricant residues, dirt, waxes, lead, copper or plastic particles that have accumulated in the action, chamber or firing mechanism of a firearm. Many gun cleaners are only solvents which perform a degreasing action, but do very little to dissolve carbon residues. This product will soften and dissolve these materials and help flush them from the firearm with a minimum of physical scraping. Masters Action & Gun Cleaner is formulated to scrub these materials from your firearm and prepare it for re-lubrication without causing dried out appearance that some firearm cleaning solvents produce. Masters Action & Gun Cleaner contains a synthetic lubricant component which penetrates the close fitting and inaccessible areas of your firearm to leave a slight amount of residual lubrication and corrosion protection.
Directions for Use -
1. Make sure the firearm is unloaded.
2. Field strip the firearm, to expose as much of the action surface as possible. Wet the action surfaces with Masters Gun Cleaner. The spray extension tube can be used to direct a spray stream into tight areas where residue and dirt often accumulates, or into areas that are not readily accessible. Spray gas chambers, rings and area around locking lug surfaces.
3. Use a cleaning brush or pick to disturb or loosen built up residue that may have accumulated in crevices or critical areas such as around extractors, ejectors, gas chambers, feed ramps or locking lugs.
4. Use a spray stream of Masters Gun Cleaner to flush away the loosened and dissolved material.
5. Repeat steps 3 and 4, as needed.
6. Use clean patches to wipe and further verify cleanliness of the firearm surfaces.
7. Relubricate and protect the action and moving parts using Masters OGS-3 Gun Oil or Masters Synthetic Spray Gun Oil.
Note: Use caution when spraying cleaner over walking surfaces. Over spray can cause a slip hazard and should be removed if present on floors.
Go back to top
Masters Bore Cleaner
Go back to top - Print this Description
NOW AVAILABLE
Product Description - Masters Bore Cleaner is formulated to chemically scrub, strip and remove built up lubricants, carbon, powder, grease, waxes, lead, copper, plastic and even Moly residues that have accumulated within your bore. Specially formulated solvents delivered with a powerful stream perform a degreasing action that softens and dissolves these materials, then blasts them from the bore and firearm, freely and effectively.
Directions for Use
1. Make sure the firearm is unloaded.
2. Masters Bore Cleaner can be sprayed directly into chamber or barrel. CAUTION: Avoid overspray on to external firearm surfaces and surrounding area. Masters Bore Cleaner is very aggressive and should remain inside the bore. Extended contact with delicate finishes and some types of plastic could cause damage. It is not recommended or necessary to soak bores over night or for long periods of time.
3. Following initial wetting of the bore, use a patch to wipe out softened residue.
4. Use the correct sized copper or steel brush to loosen and dislodge remaining residue. Several passes should be made, traveling the full length of the bore, before reversing travel. If possible , always clean from the chamber end of the barrel to avoid cleaning rod contact with the muzzle or crown. Use of a rod guide is recommended. The cleaning rod should also be wiped frequently to remove any residues that may be present.
5. Following brushing, spray Masters Bore Cleaner on a cleaning patch and repeat step 2 twice. Always use a clean and rewetted patch.
6. Alternate steps 5 and 6 until patches come out clean following brushing. It is normal for this process to be repeated several times to thoroughly and properly clean a firearm.
7. Complete the bore cleaning process by passing several dry patches through the bore to remove any remaining cleaning solvent.
8. Following cleaning of the firearm bore, Masters Action & Gun Cleaner should be used to clean the firearm action and external surfaces. Use a cleaning brush or pick to disturb or loosen built up residue that has accumulated in crevices or critical areas such as around extractors, ejectors, gas chambers, feed ramps or locking lugs. This residue can then be flushed away using the Masters Action & Gun Cleaner.
9. Re-lubricate and protect the action, bore and moving parts using Masters OGS-3 Synthetic Gun Oil and/or Masters Synthetic Spray Lubricant / Protectant.
Note: USE CAUTION ALWAYS. Master Bore Cleaner is an aggressive solvent that may harm some surfaces and finishes. Always know where residual bore cleaner will fall and avoid contract with finished floors. Some gun sights (plastic) may be affected by this product. Avoid contact. Always use eye protection when spraying cleaning products.
Go back to top